12
23. Attach the end of the Short Cable (47) to the “U”-
bracket (43) with an M8 Washer (71) and an M8
Nylon Locknut (69).
Note: Do not completely
tighten the Locknut; it should be threaded
onto the Cable so that two threads show past
the Locknut, as shown in the inset drawing.
24. Locate the Low Cable (48). Attach the Cable
inside the Base (1) with an M10 x 65mm Bolt
(55), two M10 Washers (70), two 10mm x 22mm
Spacers (51), and an M10 Nylon Locknut (68).
22. Wrap the Short Cable (47) over a 90mm Pulley
(34). Attach the Pulley and two Finger Guards
(
35) to the Double “U”-bracket (42) with an M10 x
46mm Bolt (53) and an M10 Nylon Locknut (68).
53
47
3
5
35
34
6
8
42
22
47
71
69
43
23
51
68
1
70
24
48
25. Route the Low Cable (48) over a 90mm Pulley
(34).
Attach the Pulley
, a Cable
T
rap (36), and
two Finger Guards (35) to the second set of holes
from the bottom of the two Pulley Plates (44) with
an M10 x 52mm Bolt (52) and an M10 Nylon
Locknut (68).
Make sure that the Cable T
rap is
oriented to hold the Cable in the groove of the
Pulley.
44
52
35
36
34
35
48
68
25
9
12. Route the High Cable (50) over a 90mm Pulley
(34) and down through the T
op Frame (4). Attach
the Pulley and a Cable Trap (36) to the bracket
on the Top Frame with an M10 x 52mm Bolt (52)
and an M10 Nylon Locknut (68).
Make sure the
Cable Trap is oriented to hold the Cable in the
groove of the Pulley.
13.
Route the High Cable (50) under a 90mm Pulley
(34).
Attach the Pulley
, a Cable Trap (36), and
two Finger Guards (35) to the second set of holes
from the top of the two Pulley Plates (44) with an
M10 x 52mm Bolt (52) and an M10 Nylon Locknut
(68).
Make sure that the Cable Trap is oriented
to hold the Cable in the groove of the Pulley.
10. Insert the post on the Left Arm (7) through the
hole in the Press Frame (5). Make sure the Arm
i
s behind the indicated bracket on the Press
Frame.
Slide a 25mm Washer (29) over the post on the
Left Arm (7). Attach an M6 x 43mm Bolt (61) to
the post with an M6 Nylon Locknut (72). Make
sure the Locknut and the head of the Bolt are
over the edge of the Washer, as shown in the
inset drawing.
Press a 25mm Round Outer Cap (27) onto the
top of the post on the Left Arm (7).
Repeat this step with the Right Arm (6).
11. See the CABLE DIAGRAM on page 17 for prop-
er cable routing.
Locate the High Cable (50). Route the threaded
shaft end of the Cable up through the Top Frame
(4) and over a 90mm Pulley (34). Attach the
Pulley inside the Top Frame with an M10 x 65mm
Bolt (55), two M10 Washers (70), two M10 x
12.5mm Spacers (37), and an M10 Nylon Locknut
(68).
27
29
72
7
6
5
10
61
36
52
50
34
68
4
50
34
37
37
70
70
68
55
4
11
68
44
36
44
35
35
34
50
12
13
52
CABLE ASSEMBLY
29
61
72
Post
B
racket
47
69
43
55
70
(16 Seiten)
(16 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern